01The verdict: is Kenmore water safe?
Kenmore's drinking water has significant quality concerns based on EPA testing data. With a grade of B- (72.2/100), the system has issues across multiple categories. A water filter is recommended for all residents. The city's 1 water system serves approximately 105,105 residents using surface water (rivers, lakes, or reservoirs).
Lead is over its legal limit
Measured at 36.0 ppb against the EPA Action Level of 15 ppb. The ledger below shows how far over — and which filter removes it.
See the measurement ↓No forever chemicals detected
UCMR 5 laboratory testing found no PFAS compounds above detection thresholds in this system.
See PFAS results ↓A flood-prone service area
10 federal disaster declarations on record. After severe weather, watch for boil-water advisories.
See the risk factors ↓Kenmore's drinking water received a grade of B- (72.2 out of 100), indicating fair water quality. The city's 1 water system serves approximately 105,105 residents using purchased surface water.
Lead levels were measured at 36.0 ppb (90th percentile), which exceeds the EPA action level of 15 ppb. PFAS testing under UCMR 5 found no detectable forever chemicals. The system has 5 violations on record, including 0 health-based violations. 3 remain unresolved.
Kenmore ranks #160 out of 294 cities in Washington for water quality, placing it below average in the state. The city draws from surface water sources, which are more susceptible to seasonal runoff and agricultural contamination, requiring extensive multi-barrier treatment including coagulation, filtration, and disinfection. Hexavalent chromium (chromium-6) was detected at 0.09 µg/L in UCMR 3 testing. While below California's 10 µg/L limit and with no federal MCL set, residents sensitive to this contaminant may consider reverse osmosis filtration. Lead levels exceed the EPA action level of 15 ppb, which typically indicates aging lead service lines or lead solder in the distribution system. An NSF 53-certified filter is strongly recommended for drinking and cooking water.
02What's in Kenmore's water
Every contaminant flagged in Kenmore, on one shared scale: distance to its own legal limit. The red line is the limit — anything past it is out of compliance, and the closer a bar gets, the less headroom the system has.
Over Limit — EPA Action Level: 15 ppb
Exceeds the EPA action level. Lead enters at the service line, not the treatment plant — your address matters more than the city average. Lead service line replacement and an NSF 53-certified point-of-use filter are recommended.Full contaminants report
| Contaminant | Detected Level | EPA Limit | Unit | Category | Status |
|---|---|---|---|---|---|
| Lead (90th percentile) LeadHeavy Metal A toxic heavy metal that can leach into drinking water from older pipes, solder, and fixtures. No amount of lead in water is considered safe. Health EffectsBrain and nervous system damage in children, kidney damage, high blood pressure, and reproductive problems in adults. EPA Limit15 ppb action level Common SourcesCorrosion of lead pipes, lead solder, brass faucets, and household plumbing. | 36.0 | 15 | ppb | Inorganic | Over Limit |
| 11Cl-PF3OUdS | ND | HI | µg/L | PFAS | Not Detected |
| 4:2 FTS | ND | HI | µg/L | PFAS | Not Detected |
| 6:2 FTS 6:2 FTSPFAS A fluorotelomer sulfonate commonly found at sites contaminated with aqueous film-forming foam (AFFF) used in firefighting. Health EffectsPotential liver toxicity and endocrine disruption. Less studied but identified as a contaminant of concern. EPA LimitNo individual MCL (not yet regulated) Common SourcesFirefighting foam (AFFF), airports, military bases, and industrial facilities. | ND | HI | µg/L | PFAS | Not Detected |
| 8:2 FTS | ND | HI | µg/L | PFAS | Not Detected |
| 9Cl-PF3ONS | ND | HI | µg/L | PFAS | Not Detected |
| ADONA | ND | HI | µg/L | PFAS | Not Detected |
| HFPO-DA HFPO-DA (GenX)PFAS A replacement for PFOA in manufacturing, marketed as safer but still a persistent "forever chemical." Also known as GenX. Health EffectsLiver and kidney effects, reproductive toxicity, immune system effects, and potential cancer risk. EPA Limit10 ppt MCL Common SourcesFluoropolymer manufacturing (used as PFOA replacement), industrial wastewater discharge. | ND | 0.01 | µg/L | PFAS | Not Detected |
| lithium LithiumInorganic A naturally occurring alkali metal found in groundwater. Monitored under UCMR 5 to assess occurrence in drinking water. Health EffectsKidney effects at high doses. Low-level exposure effects under study; some research suggests neurological effects. EPA LimitNo MCL (monitoring only under UCMR 5) Common SourcesNatural mineral deposits, geothermal water, and industrial discharge. | ND | HI | µg/L | PFAS | Not Detected |
| NEtFOSAA | ND | HI | µg/L | PFAS | Not Detected |
| NFDHA | ND | HI | µg/L | PFAS | Not Detected |
| NMeFOSAA | ND | HI | µg/L | PFAS | Not Detected |
| PFBA PFBAPFAS One of the shortest-chain PFAS compounds. Very mobile in water and difficult to remove with standard filtration. Health EffectsThyroid effects, potential developmental toxicity. Shorter half-life in body than long-chain PFAS. EPA LimitNo individual MCL (not yet regulated) Common SourcesDegradation of longer-chain PFAS, industrial discharge, and firefighting foam. | ND | HI | µg/L | PFAS | Not Detected |
| PFBS PFBSPFAS A short-chain PFAS used as a replacement for PFOS. While it clears the body faster than long-chain PFAS, it still persists in the environment. Health EffectsThyroid effects, reproductive and developmental toxicity, kidney effects. EPA LimitPart of Hazard Index (1.0) Common SourcesIndustrial discharge, firefighting foam, and as a replacement chemical in manufacturing. | ND | HI | µg/L | PFAS | Not Detected |
| PFDA | ND | HI | µg/L | PFAS | Not Detected |
| PFDoA | ND | HI | µg/L | PFAS | Not Detected |
| PFEESA | ND | HI | µg/L | PFAS | Not Detected |
| PFHpA PFHpAPFAS A medium-chain PFAS compound found in various environmental samples. Less studied than PFOA/PFOS but still considered a contaminant of concern. Health EffectsLiver effects, potential developmental toxicity, and endocrine disruption. EPA LimitPart of Hazard Index (1.0) Common SourcesDegradation of longer-chain PFAS, industrial discharge, and contaminated water sources. | ND | HI | µg/L | PFAS | Not Detected |
| PFHpS | ND | HI | µg/L | PFAS | Not Detected |
| PFHxA PFHxAPFAS A short-chain PFAS replacement chemical widely used after manufacturers phased out longer-chain PFAS. Very commonly detected in water. Health EffectsLiver and kidney effects, potential thyroid disruption. Considered less toxic than long-chain PFAS but still persistent. EPA LimitNo individual MCL (not yet regulated) Common SourcesIndustrial processes, firefighting foam (AFFF), food packaging, and textile treatment. | ND | HI | µg/L | PFAS | Not Detected |
| PFHxS PFHxSPFAS A medium-chain PFAS found in firefighting foam and consumer products. It has a long half-life in the human body, similar to long-chain PFAS. Health EffectsImmune system effects, thyroid disruption, and potential reproductive and developmental harm. EPA LimitPart of Hazard Index (1.0) Common SourcesFirefighting foam (AFFF), waterproof textiles, food packaging, and industrial discharge. | ND | HI | µg/L | PFAS | Not Detected |
| PFMBA | ND | HI | µg/L | PFAS | Not Detected |
| PFMPA | ND | HI | µg/L | PFAS | Not Detected |
| PFNA PFNAPFAS A long-chain PFAS compound used in manufacturing fluoropolymers. It bioaccumulates in the body and is very persistent in the environment. Health EffectsDevelopmental effects, liver toxicity, immune suppression, and potential cancer risk. EPA LimitPart of Hazard Index (1.0) Common SourcesFluoropolymer manufacturing, industrial emissions, and contaminated water sources. | ND | HI | µg/L | PFAS | Not Detected |
| PFOA PFOAPFAS A long-chain PFAS ("forever chemical") once widely used in nonstick coatings and firefighting foam. It persists in the body and environment for years. Health EffectsLinked to kidney and testicular cancer, thyroid disease, elevated cholesterol, and reproductive issues. EPA Limit4.0 ppt MCL Common SourcesIndustrial discharge, firefighting foam (AFFF), nonstick cookware manufacturing, and contaminated groundwater. | ND | 0.004 | µg/L | PFAS | Not Detected |
| PFOS PFOSPFAS A long-chain PFAS compound historically used in stain-resistant coatings and firefighting foam. One of the most studied and persistent PFAS chemicals. Health EffectsLiver damage, immune system suppression, thyroid disruption, increased cholesterol, and potential cancer risk. EPA Limit4.0 ppt MCL Common SourcesFirefighting foam (AFFF), industrial sites, stain-resistant fabric treatments, and contaminated groundwater. | ND | 0.004 | µg/L | PFAS | Not Detected |
| PFPeA PFPeAPFAS A short-chain PFAS compound commonly detected in drinking water. One of the most frequently found PFAS in UCMR 5 monitoring. Health EffectsLess studied than PFOA/PFOS. Potential liver and thyroid effects. Research is ongoing. EPA LimitNo individual MCL (not yet regulated) Common SourcesIndustrial discharge, firefighting foam degradation, and consumer products. | ND | HI | µg/L | PFAS | Not Detected |
| PFPeS | ND | HI | µg/L | PFAS | Not Detected |
| PFTA | ND | HI | µg/L | PFAS | Not Detected |
| PFTrDA | ND | HI | µg/L | PFAS | Not Detected |
| PFUnA | ND | HI | µg/L | PFAS | Not Detected |
Cities ranked by 90th-percentile lead PF PFAS in Washington
Cities ranked by compounds detected Cu Copper in Washington
Cities ranked by 90th-percentile copper
03Kenmore's ten-year track record
Each box is one year. A green check means no EPA violations; a numbered badge counts that year's violations — red if any were health-based, amber if they were monitoring or paperwork issues. The system has 5 violations on record, including 0 health-based violations. 3 remain unresolved.
All ten of the last ten years were clean — no EPA violations recorded for Kenmore.
36ppb(1992)
One sampling round on record — 240% of the 15ppb EPA action level. Sampled at higher-risk homes (90th percentile).
04Where Kenmore's water comes from
Kenmore's drinking water comes primarily from surface water sources such as rivers, lakes, or reservoirs.
Purchased Surface Water
Rivers, lakes, or reservoirs — more exposed to runoff, agriculture, and seasonal swings than groundwater.
Wholesale supplier
Multi-barrier treatment: coagulation, sedimentation, filtration, and disinfection to meet EPA standards.
1 system
1 water system (1 wholesaler), operated under local government ownership.
105,105 people
Residents served across Kenmore's service area.
Surface water systems require multi-stage treatment including coagulation, sedimentation, filtration, and disinfection to meet EPA Safe Drinking Water Act standards. These sources can be impacted by seasonal changes, stormwater runoff, upstream agriculture, and industrial discharge. The system is operated by local government ownership and serves approximately 105,105 people through 1 water system.
| System name | PWSID | Population | Source |
|---|---|---|---|
| NORTHSHORE UTILITY DISTRICT | WA5340800 | 105,105 | Purchased Surface Water |
05Pressure on Kenmore's watershed
Outside forces that shape what reaches the treatment plant. None of these is a verdict on the tap by itself — but each adds pressure worth knowing about.
Industrial discharge
5 facilities within 10 miles reported 2 lb released to surface water in the latest EPA Toxics Release Inventory. Proximity doesn't equal tap contamination — treatment and hydrology decide — but it's pressure on the watershed.
Flood & storm history
10 federal disaster declarations on record for King County. Flooding and severe storms can overwhelm treatment plants, cause sewage overflows, and push runoff into supplies.
06How Kenmore compares
Scores for nearby Washington cities on one line, with the average marked.
dashed line = Washington average (53/100)
Kenmore scores 72.2/100 — above the Washington average of 53/100. It outscores 7 of 10 nearby cities. Full Washington rankings →
42.3 / 100FTacoma, WA
32.2 / 100FVancouver, WA
32.9 / 100FSpokane, WA
39.2 / 100FKent, WA
44.4 / 100ABellevue, WA
91.6 / 100
Compare all cities in the county — grades, violations, and contaminant data side by side.→
07What to do at home
Steps matched to what testing actually found in Kenmore's water — not generic advice.
Filter drinking & cooking water
NSF 53-certified pitcher or under-sink filter. Lead level (36.0 ppb) exceeds the EPA action level of 15 ppb
Compare tested filters →Flush taps & check your service line
Lead leaches from pipes as water sits. Run cold water 30 seconds before drinking (especially mornings), and ask the utility whether your address still has a lead service line.
Lead risks explained →Watch for Kenmore alerts
This area has a history of flood declarations — after severe weather, watch for boil-water advisories from the utility, and check the live alerts on this page.
All water alerts →Frequently asked questions
Is Kenmore, WA tap water safe to drink?
Kenmore's water quality earned a grade of B- (72.2/100). Some concerns have been identified. Consider a water filter for an extra layer of protection. The city ranks #160 out of 294 cities tested in Washington.
What contaminants are in Kenmore's water?
Lead was measured at 36.0 ppb (90th percentile). No PFAS compounds were detected. 5 violations are on record.
How is Kenmore's water quality grade calculated?
The grade is based on four factors: violation history (40%), lead and copper levels (25%), PFAS contamination (25%), and regulatory compliance (10%). The score is also adjusted based on how complete the available data is. See our methodology page for full details.
Do I need a water filter in Kenmore?
Yes — lead levels exceed the EPA action level of 15 ppb. We recommend an NSF 53-certified filter or reverse osmosis system. Based on current data, basic filtration should suffice for additional peace of mind.
Where does Kenmore's water come from?
Kenmore's water is sourced from Purchased surface water. The city has 1 water system serving approximately 105,105 residents.
How does Kenmore's water compare to other cities?
Kenmore ranks #160 out of 294 cities in Washington (better than 46% of state cities) and #10270 out of 15382 cities nationally (33th percentile). The grade of B- reflects the combined assessment of violation history, lead and copper levels, PFAS contamination, and regulatory compliance.